Showing all 7 results

Show sidebar
-49%
Close

Breakout Kit for Raspberry Pi B w& 40pin to 26pin Cable

38.38$ 19.50$ + Vat
Description Introduction: This is a T-type breakout kit used for extending the GPIO interface on Raspberry Pi to breadboard. It
-44%
Close

flat cable;26p-L210-2651-28AWG

17.80$ 10.00$ + Vat
Descriptions Cable Assembly 2m 40 to 26 POS IDC Connector to IDC Connector RCP-RCP Verical Seeedstudio Raspberry Pi A+/B+/2 40pin
-52%
Close

Tinker Wires 20cm Model

15.60$ 7.55$ + Vat
Tanım: Toolkit Wire, Tinkerkit sensör ve eyleyicilerinin (actuator) Tinkerkit Sensor Shieldlar ile bağlantısını sağlamak için yapılmış 3’lü JST konnektöre sahip
-3%
Close

Tinkerkit DMX Receiver – Relay

55.33$ 53.56$ + Vat
Provide extra power support for your circuits. Connect the module to the DMX Master Shield which in turn sits on top of your Arduino board. Overview
  • Four relays
  • Suitable for 12 V power supply
  • Individual relay supports up to 220 V @ 10 A
  • Also functions as a standalone USB board
 
-48%
Close

Tinkerkit Wires 50cm Model

16.33$ 8.50$ + Vat
Overview 50 cm long wires for the TinkerKit with a 3 pin jumper on both sides. Mouser Electronics Authorized Distributor
-15%
Close

WAGO Power supply 24 VDC

325.00$ 275.00$ + Vat

Power supply; Pro 2; 1-phase; 24 VDC output voltage; 10 A output current; TopBoost + PowerBoost; communication capability

Details
Technical Data
Input
Phases 1
Nominal input voltage Ui nom AC 100 … 240 V
Input voltage range AC 90 … 264 V; DC 130 … 373 V
Nominal mains frequency range 47 … 63 Hz; 0 Hz
Input current Ii ≤ 1.2 A (240 VAC; Nominal load); ≤ 2.7 A (100 VAC; Nominal load)
Inrush current ≤ 11 A (after 1 ms)
Power factor correction (PFC) Active
Mains failure hold-up time ≥ 25 ms (230 VAC)
More
Output
Nominal output voltage Uo nom DC 24 V (SELV)
Output voltage range DC 24 … 28 V (adjustable)
Default setting DC 24 V
Nominal output current Io nom 10 A (24 VDC)
Nominal output power 240 W
Control deviation ≤ 1 %
Residual ripple ≤ 70 mV (peak-to-peak)
Current limitation 1.1 x Io nom (typ.)
Overload behavior TopBoost/PowerBoost/Time-limited constant current mode (other overload behaviors can be set)
PowerBoost DC 15 A (5 s)
More
Signaling and communication
Signaling Optical status indication (DC OK; load; warning and error states) Digital signal input and output (DI/DO)
Communication Communication interface, can be used with WAGO USB Communication Cable (750-923) or IO-Link Communication Module (2789-9080) or Modbus RTU Communication Module (2789-9015)
Efficiency/Power losses:
Power loss Pl ≤ 1 W (Stand-by); ≤ 2.2 W (No load); ≤ 12 W (230 VAC; Nominal load)
Efficiency (typ.) 95.3 % (230 VAC; 10 ADC; 25 °C)
Fuse protection:
Internal fuse T 6.3 A / 250 VAC
Required backup fusing An external DC fuse is required for the DC input voltage.
Recommended backup fusing 16 A (for USA/Canada: 15 A)
Safety and protection:
Isolationsspannung (Pri.-Sek., AC) 3,510 V
Isolationsspannung (Pri.-PE, AC) 2,200 V
Isolation voltage (Sec.-GND) DC 0.5 kV
Isolation voltage (Sec.-Signal) DC 0.5 kV
Protection class I
Protection type IP20 (per EN 60529)
Resistance to reverse feed ≤ DC 35 V
Overvoltage category III (≤ 2000 m a. s.l.); II (> 2000 m a. s.l.)
Transient suppression (primary) Yes
Overvoltage protection; secondary Internal protective circuit ≤ 35 VDC (in the event of a fault)
Short-circuit-protected Yes
Open-circuit-proof Yes
Parallel operation Yes
Series operation Yes
MTBF > 1,200,000 h (per IEC 61709)
More
Connection data
Connection type (1) Input/Output/Signaling
Connection technology CAGE CLAMP®
WAGO Connector WAGO 721 Series
Solid conductor 0.08 … 2.5 mm² / 28 … 12 AWG
Fine-stranded conductor 0.08 … 2.5 mm² / 28 … 12 AWG
Fine-stranded conductor; with insulated ferrule 0.25 … 1.5 mm² / 20 … 16 AWG
Fine-stranded conductor; with uninsulated ferrule 0.25 … 2.5 mm² / 20 … 14 AWG
Strip length 8 … 9 mm / 0.31 … 0.35 inch
More
Geometrical Data
Width 50 mm / 1.969 inch
Height 130 mm / 5.118 inch
Depth from upper edge of DIN-rail 130 mm / 5.118 inch
Note (dimensions) Height without connector Height with connector: 166 mm
Mechanical data
Mounting type DIN-35 rail (EN 60715)
Material Data
Weight 1000 g
Environmental Requirements
Surrounding air temperature (operation) -25 … 70 °C (Device starts at −40 °C (type-tested))
Surrounding air temperature (storage) -40 … 85 °C
Relative humidity 5 … 96 % (no condensation permissible)
Derating −3 %/K (> +55 °C and Ui < 230 VAC); −3 %/K (> +60 °C and Ui ≥ 230 VAC)
Pollution degree 2
Climatic category 3K3 (per EN 60721)
Operating altitude (max.) 5000 m
More
Standards and specifications
Conformity marking CE
Standards/specifications EN 61010-1; EN 61010-2-201; EN 61204-3; UL 61010-1; UL 61010-2-201
Commercial data
Packaging type BOX
Country of origin CN
GTIN 4055143907330
Customs tariff number 85044082900
-52%
Close

Wall Adapter Power Supply – 6.5VDC 2A

12.30$ 5.90$ + Vat
High quality switching ‘wall wart’ AC to DC 6.5V 2A wall power supply. It is sperical designed for Rainbowduino, also