WAGO Power supply 24 VDC

325.00$ 275.00$ + Vat

Power supply; Pro 2; 1-phase; 24 VDC output voltage; 10 A output current; TopBoost + PowerBoost; communication capability

Details
Technical Data
Input
Phases 1
Nominal input voltage Ui nom AC 100 … 240 V
Input voltage range AC 90 … 264 V; DC 130 … 373 V
Nominal mains frequency range 47 … 63 Hz; 0 Hz
Input current Ii ≤ 1.2 A (240 VAC; Nominal load); ≤ 2.7 A (100 VAC; Nominal load)
Inrush current ≤ 11 A (after 1 ms)
Power factor correction (PFC) Active
Mains failure hold-up time ≥ 25 ms (230 VAC)

More

Output
Nominal output voltage Uo nom DC 24 V (SELV)
Output voltage range DC 24 … 28 V (adjustable)
Default setting DC 24 V
Nominal output current Io nom 10 A (24 VDC)
Nominal output power 240 W
Control deviation ≤ 1 %
Residual ripple ≤ 70 mV (peak-to-peak)
Current limitation 1.1 x Io nom (typ.)
Overload behavior TopBoost/PowerBoost/Time-limited constant current mode (other overload behaviors can be set)
PowerBoost DC 15 A (5 s)

More

Signaling and communication
Signaling Optical status indication (DC OK; load; warning and error states)
Digital signal input and output (DI/DO)
Communication Communication interface, can be used with WAGO USB Communication Cable (750-923) or IO-Link Communication Module (2789-9080) or Modbus RTU Communication Module (2789-9015)
Efficiency/Power losses:
Power loss Pl ≤ 1 W (Stand-by); ≤ 2.2 W (No load); ≤ 12 W (230 VAC; Nominal load)
Efficiency (typ.) 95.3 % (230 VAC; 10 ADC; 25 °C)
Fuse protection:
Internal fuse T 6.3 A / 250 VAC
Required backup fusing An external DC fuse is required for the DC input voltage.
Recommended backup fusing 16 A (for USA/Canada: 15 A)
Safety and protection:
Isolationsspannung (Pri.-Sek., AC) 3,510 V
Isolationsspannung (Pri.-PE, AC) 2,200 V
Isolation voltage (Sec.-GND) DC 0.5 kV
Isolation voltage (Sec.-Signal) DC 0.5 kV
Protection class I
Protection type IP20 (per EN 60529)
Resistance to reverse feed ≤ DC 35 V
Overvoltage category III (≤ 2000 m a. s.l.); II (> 2000 m a. s.l.)
Transient suppression (primary) Yes
Overvoltage protection; secondary Internal protective circuit
≤ 35 VDC (in the event of a fault)
Short-circuit-protected Yes
Open-circuit-proof Yes
Parallel operation Yes
Series operation Yes
MTBF > 1,200,000 h (per IEC 61709)

More

Connection data
Connection type (1) Input/Output/Signaling
Connection technology CAGE CLAMP®
WAGO Connector WAGO 721 Series
Solid conductor 0.08 … 2.5 mm² / 28 … 12 AWG
Fine-stranded conductor 0.08 … 2.5 mm² / 28 … 12 AWG
Fine-stranded conductor; with insulated ferrule 0.25 … 1.5 mm² / 20 … 16 AWG
Fine-stranded conductor; with uninsulated ferrule 0.25 … 2.5 mm² / 20 … 14 AWG
Strip length 8 … 9 mm / 0.31 … 0.35 inch

More

Geometrical Data
Width 50 mm / 1.969 inch
Height 130 mm / 5.118 inch
Depth from upper edge of DIN-rail 130 mm / 5.118 inch
Note (dimensions) Height without connector
Height with connector: 166 mm
Mechanical data
Mounting type DIN-35 rail (EN 60715)
Material Data
Weight 1000 g
Environmental Requirements
Surrounding air temperature (operation) -25 … 70 °C (Device starts at −40 °C (type-tested))
Surrounding air temperature (storage) -40 … 85 °C
Relative humidity 5 … 96 % (no condensation permissible)
Derating −3 %/K (> +55 °C and Ui < 230 VAC); −3 %/K (> +60 °C and Ui ≥ 230 VAC)
Pollution degree 2
Climatic category 3K3 (per EN 60721)
Operating altitude (max.) 5000 m

More

Standards and specifications
Conformity marking CE
Standards/specifications EN 61010-1; EN 61010-2-201; EN 61204-3; UL 61010-1; UL 61010-2-201
Commercial data
Packaging type BOX
Country of origin CN
GTIN 4055143907330
Customs tariff number 85044082900
SKU: 2787-2146 Category:
Description
Details
Technical Data
Input
Phases 1
Nominal input voltage Ui nom AC 100 … 240 V
Input voltage range AC 90 … 264 V; DC 130 … 373 V
Nominal mains frequency range 47 … 63 Hz; 0 Hz
Input current Ii ≤ 1.2 A (240 VAC; Nominal load); ≤ 2.7 A (100 VAC; Nominal load)
Inrush current ≤ 11 A (after 1 ms)
Power factor correction (PFC) Active
Mains failure hold-up time ≥ 25 ms (230 VAC)

More

Output
Nominal output voltage Uo nom DC 24 V (SELV)
Output voltage range DC 24 … 28 V (adjustable)
Default setting DC 24 V
Nominal output current Io nom 10 A (24 VDC)
Nominal output power 240 W
Control deviation ≤ 1 %
Residual ripple ≤ 70 mV (peak-to-peak)
Current limitation 1.1 x Io nom (typ.)
Overload behavior TopBoost/PowerBoost/Time-limited constant current mode (other overload behaviors can be set)
PowerBoost DC 15 A (5 s)

More

Signaling and communication
Signaling Optical status indication (DC OK; load; warning and error states)
Digital signal input and output (DI/DO)
Communication Communication interface, can be used with WAGO USB Communication Cable (750-923) or IO-Link Communication Module (2789-9080) or Modbus RTU Communication Module (2789-9015)
Efficiency/Power losses:
Power loss Pl ≤ 1 W (Stand-by); ≤ 2.2 W (No load); ≤ 12 W (230 VAC; Nominal load)
Efficiency (typ.) 95.3 % (230 VAC; 10 ADC; 25 °C)
Fuse protection:
Internal fuse T 6.3 A / 250 VAC
Required backup fusing An external DC fuse is required for the DC input voltage.
Recommended backup fusing 16 A (for USA/Canada: 15 A)
Safety and protection:
Isolationsspannung (Pri.-Sek., AC) 3,510 V
Isolationsspannung (Pri.-PE, AC) 2,200 V
Isolation voltage (Sec.-GND) DC 0.5 kV
Isolation voltage (Sec.-Signal) DC 0.5 kV
Protection class I
Protection type IP20 (per EN 60529)
Resistance to reverse feed ≤ DC 35 V
Overvoltage category III (≤ 2000 m a. s.l.); II (> 2000 m a. s.l.)
Transient suppression (primary) Yes
Overvoltage protection; secondary Internal protective circuit
≤ 35 VDC (in the event of a fault)
Short-circuit-protected Yes
Open-circuit-proof Yes
Parallel operation Yes
Series operation Yes
MTBF > 1,200,000 h (per IEC 61709)

More

Connection data
Connection type (1) Input/Output/Signaling
Connection technology CAGE CLAMP®
WAGO Connector WAGO 721 Series
Solid conductor 0.08 … 2.5 mm² / 28 … 12 AWG
Fine-stranded conductor 0.08 … 2.5 mm² / 28 … 12 AWG
Fine-stranded conductor; with insulated ferrule 0.25 … 1.5 mm² / 20 … 16 AWG
Fine-stranded conductor; with uninsulated ferrule 0.25 … 2.5 mm² / 20 … 14 AWG
Strip length 8 … 9 mm / 0.31 … 0.35 inch

More

Geometrical Data
Width 50 mm / 1.969 inch
Height 130 mm / 5.118 inch
Depth from upper edge of DIN-rail 130 mm / 5.118 inch
Note (dimensions) Height without connector
Height with connector: 166 mm
Mechanical data
Mounting type DIN-35 rail (EN 60715)
Material Data
Weight 1000 g
Environmental Requirements
Surrounding air temperature (operation) -25 … 70 °C (Device starts at −40 °C (type-tested))
Surrounding air temperature (storage) -40 … 85 °C
Relative humidity 5 … 96 % (no condensation permissible)
Derating −3 %/K (> +55 °C and Ui < 230 VAC); −3 %/K (> +60 °C and Ui ≥ 230 VAC)
Pollution degree 2
Climatic category 3K3 (per EN 60721)
Operating altitude (max.) 5000 m

More

Standards and specifications
Conformity marking CE
Standards/specifications EN 61010-1; EN 61010-2-201; EN 61204-3; UL 61010-1; UL 61010-2-201
Commercial data
Packaging type BOX
Country of origin CN
GTIN 4055143907330
Customs tariff number 85044082900
Additional information
Weight 1 kg
Dimensions 5 x 13 x 13 cm
Brand

WAGO

Reviews (0)

Reviews

There are no reviews yet.

Only logged in customers who have purchased this product may leave a review.

Shipping & Delivery

MAECENAS IACULIS

Vestibulum curae torquent diam diam commodo parturient penatibus nunc dui adipiscing convallis bulum parturient suspendisse parturient a.Parturient in parturient scelerisque nibh lectus quam a natoque adipiscing a vestibulum hendrerit et pharetra fames nunc natoque dui.

ADIPISCING CONVALLIS BULUM

  • Vestibulum penatibus nunc dui adipiscing convallis bulum parturient suspendisse.
  • Abitur parturient praesent lectus quam a natoque adipiscing a vestibulum hendre.
  • Diam parturient dictumst parturient scelerisque nibh lectus.

Scelerisque adipiscing bibendum sem vestibulum et in a a a purus lectus faucibus lobortis tincidunt purus lectus nisl class eros.Condimentum a et ullamcorper dictumst mus et tristique elementum nam inceptos hac parturient scelerisque vestibulum amet elit ut volutpat.